禹城彩鋼巖棉復合板的安裝方法如下：

　　The installation method of Yucheng color steel rock wool composite board is as follows:

　　1、 基層處理

　　1. Grassroots treatment

　　確認待安裝處無灰塵、無油脂、無銹蝕、無松動等，表面干燥，如有防潮防腐需求，可適當采取涂層處理，找平層達到要求，基層驗收合格。

　　Confirm that the installation site is free of dust, grease, rust, looseness, etc., and the surface is dry. If there is a need for moisture and corrosion prevention, appropriate coating treatment can be taken, and the leveling layer meets the requirements. The base acceptance is qualified.

　　2、 彈線控制和懸掛基準線

　　2. Bounce line control and suspension reference line

　　根據建筑實際立面設計和外墻技術要求，彈出門窗水平線、垂直控制線和裝飾縫線等，在建筑外陰陽角和其他適當處懸掛垂直基準線和水平線，以確保安裝平整度和垂直度符合施工要求。

　　According to the actual facade design and external wall technical requirements of the building, pop out horizontal lines, vertical control lines, and decorative stitching lines for doors and windows. Hang vertical reference lines and horizontal lines at the external corners and other appropriate locations of the building to ensure that the installation flatness and verticality meet the construction requirements.

　　3、鋪設施工

　　3. Laying construction

　　挑選合適的禹城彩鋼巖棉復合板，規格和外觀尺寸偏差均在規定范圍內，裁剪下料后，按設計要求選擇復合板橫向還是豎向布置（注意橫向布置時每塊板兩個卡件，豎向布置時板上下左右各一個卡件），并用膨脹螺栓錨卡件進行固定，拼縫大小符合施工要求，板和氈的接頭對接一定要十分緊密，在多層保溫時各十字接縫應交錯分開，避免形成熱橋和冷橋。

　　Select suitable Yucheng color steel rock wool composite panels, with specifications and appearance size deviations within the specified range. After cutting and cutting, choose whether to arrange the composite panels horizontally or vertically according to the design requirements (note that each panel should have two clips for horizontal layout, and one clip for each top, bottom, left, and right of the panel for vertical layout), and fix them with expansion bolts and anchor clips. The joint size should meet the construction requirements, and the joint between the panel and felt must be very tight. In multi-layer insulation, the cross joints should be staggered and separated to avoid the formation of hot and cold bridges.

　　4、 涂抹膠粘劑

　　4. Apply adhesive

　　按比例要求配制禹城彩鋼巖棉復合板專用膠粘劑，充分攪拌后的膠粘劑應色澤均勻、新鮮良好、稠度適宜，粘度要達到使剛粘貼上的巖棉板不會下垂。將配制好的膠粘劑按規定厚度，均勻地涂抹在巖棉板上，可采用條形點粘方式進行粘接，以確保牢固可靠。

　　Prepare the special adhesive for Yucheng color steel rock wool composite board according to the proportion requirements. After thorough mixing, the adhesive should have a uniform color, fresh and good consistency, and the viscosity should be sufficient to prevent the newly pasted rock wool board from sagging. Apply the prepared adhesive evenly to the rock wool board according to the specified thickness, and use a strip point bonding method to ensure firmness and reliability.

　　本文由    禹城彩鋼復合板 友情奉獻.更多有關的知識請點擊    http://  真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Yucheng Color Steel Composite Panel. For more related knowledge, please click http:// Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned