一、選擇正規的專賣店

1、 Choose a reputable brand store

經驗告訴我們，市場假產品層出不窮，以次充好大有，對于不的業主一定要擦亮眼睛，正確識別真正的產品。知名專賣店的產品質量更有保證。如果沒有的涂料知識，選擇店是保險的了。選擇型的店，這類店的油漆質量、性能和服務承諾可靠性高。其次觀察油漆顏色，性油漆選用進口原料配制，亮光漆色澤水白，晶瑩透明，亞光漆呈半透明，略帶輕微渾濁狀，無發紅和沉淀現象;性油漆外包裝比較精美，字跡清晰美觀。

Experience tells us that fake products are constantly emerging in the market, and there are plenty of inferior products passing off as good. For unprofessional homeowners, it is important to keep their eyes open and correctly identify truly high-quality products. The product quality of well-known brand specialty stores is more guaranteed. If you don't have professional knowledge of coatings, choosing a branded store is the safest option. It is best to choose environmentally friendly brand stores, which have high paint quality, environmental performance, and reliable service commitments. Secondly, observe the color of the paint. Environmentally friendly paint is formulated with imported raw materials. The glossy paint has a water white color, crystal clear and transparent, while the matte paint is semi transparent with a slight turbidity, without redness or sedimentation; The environmentally friendly paint packaging is quite exquisite, with clear and beautiful handwriting.

二、聞氣味，辨質量

2、 Smell the odor and distinguish the quality

獲得質量認可的產品是有保證的，質量好，型油漆的氣味應該是溫和、淡雅、芳香味純正的，劣質的油漆會有一種強烈的刺鼻氣味或其它不明的異味。目前部分劣質漆也有香味，甚比香水還香，這種油漆的苯可能超標，而苯就是一種無色具有特殊芳香味的液體，對人類健康有很大的危害，因此朋友們在購買油漆時一定要聞一聞它的氣味。

Products that have obtained national quality recognition are guaranteed to have good quality. Environmentally friendly paints should have a mild, elegant, and pure aroma. Poor quality paints may have a strong pungent odor or other unknown odors. At present, some low-quality paints also have fragrance, even more fragrant than perfume. The benzene of this kind of paint may exceed the standard, and benzene is a colorless liquid with special fragrance, which is very harmful to human health. Therefore, friends must smell its smell when buying paint.

涂料防水層的施工應符合下列規定：

The construction of the waterproof coating layer should comply with the following regulations:

1、涂料涂刷前應先在基面上涂一層與涂料相容的基層處理劑

1. Before painting, a layer of base treatment agent compatible with the coating should be applied on the base surface

2、涂膜應多遍完成，涂刷應該前遍涂層干燥成膜后進行

2. The coating should be completed multiple times, and the brushing should be carried out after the previous coat has dried and formed a film

3、每遍涂刷時應交替改變涂層的涂刷方向，同層涂膜的先后搭茬寬度宜為30~50㎜

3. The direction of the coating should be alternately changed during each application, and the width of the overlapping of the same layer of coating should be 30-50mm

4、涂料防水層的施工縫應注意保護，搭接縫寬度應大于100㎜，接涂前應將其甩茬表面處理干凈

4. Attention should be paid to the protection of the construction joints of the waterproof coating layer, and the width of the lap joint should be greater than 100mm. Before applying the coating, the surface of the butt joint should be cleaned

5、涂刷程序應先做轉角處，穿墻管道，變形縫等部位的涂料加強層，后進行大面積涂刷

5. The painting procedure should first apply a coating reinforcement layer to corners, through wall pipelines, deformation joints, and other areas, and then proceed with large-scale painting

6、涂料防水層中鋪貼的脂體增強材料，同層相鄰的搭接寬度應大于100㎜，上下層接縫應錯開1/3幅寬 涂刷的防水涂料固化后形成有一定厚度的涂膜，如果涂膜厚度太薄就起不到防水作用和很難達到合理使用年限的要求，所以對各類防水涂料的涂膜厚度作了規定。 防水涂膜在滿足厚度要求的前提下，涂刷的遍數越多對成膜的密實度越好，因此涂刷時應多遍涂刷，不論是厚質涂料還是薄質涂料均不得一次成膜。 每遍涂刷應均勻，不該有露底，漏涂和堆積現象，多遍涂刷時，應待涂層干燥成膜后方可涂刷后一遍涂料，兩涂層施工間隔時間不應過長，否則，會形成分層。

6. The fat reinforcement material laid in the waterproof layer of the coating should have a lap width of more than 100mm between adjacent layers, and the joints between the upper and lower layers should be staggered by 1/3 of the width. After the waterproof coating is cured, a certain thickness of coating film is formed. If the coating film thickness is too thin, it will not have waterproof effect and it is difficult to meet the reasonable service life requirements. Therefore, regulations have been made for the coating thickness of various waterproof coatings. On the premise of meeting the thickness requirements, the more times the waterproof coating is applied, the better the compactness of the film formation. Therefore, multiple coats should be applied, and both thick and thin coatings should not form a film at once. Each coat of paint should be evenly applied, without any exposed base, missed coating, or accumulation. When applying multiple coats, the next coat of paint should be applied after the coating has dried and formed a film. The interval between the two coats should not be too long, otherwise delamination may occur.

本文由禹城鋼結構板房友情奉獻.更多有關的知識請點擊:http://我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message